Targets: set science-based reduction targets
Set your emission reduction targets under Carbon accounting → Targets. You pick a base year, add a target for each scope, and adjust it per company if needed. Next-gen checks each target against the Science Based Targets initiative (SBTi) and draws your pathway to 2050.
Targets are included in both Pro and Decarb+. With Decarb+, your targets also show in Decarbonize, in your scenarios and transition plan.
Before you start
- Get your base year right. Your targets are a percentage reduction from base-year emissions. Make sure that year's inventory is as complete as you can make it.
- Check your role. Owners can set and change targets. Other users can view them.
1. Set your base year
- Open Carbon accounting → Targets.
- In the Set the base year card, pick a year. Each option shows that year's total emissions.
- Click Set [year] as base year. The scope cards unlock.
Good to know:
- You set one base year for your whole organization. It applies to every company.
- Only years with emissions are listed. If the list is empty, add data for a past year first.
- You can change the base year later with Change base year. Your target values stay, so check that they are still SBTi aligned.
2. Add a target for each scope
- Click + Scope 1 target (or Scope 2 or 3).
- Choose your target terms. The near-term target is required. The long-term target is on by default, and you can turn it off.
- Choose the target year for each term. Years that meet SBTi are marked.
- Review the reduction. It starts at the SBTi minimum for the years you chose. You can raise it.
- Check which emission categories are included. All categories with base-year emissions are included by default. To leave one out, pick a reason. A coverage bar shows whether you still meet the SBTi minimum.
- Click Add Scope 1 target. Repeat for the other scopes.
For Scope 2, you can set an absolute reduction target, a renewable electricity target (the share of purchased electricity from renewable sources), or both.
Each scope card shows SBTi aligned or Not SBTi aligned. Hover over the warning to see why. To change or remove a target, click the pencil on its card.
SBTi minimums used
Next-gen uses the SBTi cross-sector 1.5°C approach.
| Rule | Scope 1 and 2 | Scope 3 |
|---|---|---|
| Near-term reduction per year | 4.2% | 2.5% |
| Near-term target year | 5 to 10 years after the base year | 5 to 10 years after the base year |
| Long-term reduction | 90% | 90% |
| Long-term target year | 2050 or earlier | 2050 or earlier |
| Coverage of base-year emissions | 95% | 67% near term, 90% long term |
Sector-specific approaches, such as FLAG and the energy-sector method (SDA), are not supported yet.
3. Adjust targets per company
Group with several companies? The table below the scope cards shows the consolidated target on top and every company below it. Each company follows the consolidated target unless you give it its own value.
- Click a value in the table.
- Type the new reduction. A bar shows whether it is enough: green if the group still reaches its target, orange if not. A marker shows what the company needs at least.
- Click outside or press Enter to save. Press Escape to cancel.
Some companies can do more and others less, as long as the group adds up. If it falls short, the consolidated value turns orange and shows what the group adds up to. Companies below the target get a Not aligned badge. Next-gen flags this, but does not block it.
When you change the consolidated value, you choose whether it applies to the Entire organization (company values are cleared) or Only this level (companies keep their own values).
Your pathway
The Target pathways chart shows your emission history and a dashed line for each scope target: from the base year to the near-term goal, then on to the long-term goal. Use the chips to switch between scopes.
Good to know
- Every company counts at 100% of its own emissions. Equity-share weighting is not supported yet.
- Scope 2 targets use your organization's default Scope 2 method (location-based or market-based).
- The renewable electricity target is not drawn on the chart, because it is a share of electricity, not emissions.
- Changes save as you go. There is no undo or change log for target edits yet.
- Your base-year emissions follow your live data. If you correct base-year data or factors are updated, the base-year total can change.
Next step: plan how to get there
With Decarb+, Decarbonize shows your targets next to your scenarios and transition plan, so you can see whether your planned actions are enough. Read Introducing Decarbonization.
Was this article helpful?
That’s Great!
Thank you for your feedback
Sorry! We couldn't be helpful
Thank you for your feedback
Feedback sent
We appreciate your effort and will try to fix the article